No need to hire an electrician to move up to level 2 speeds.

Parameters
Mechanical life: no-load plug in/pull out> 10000 times
Drop Load: 1 Meter / 3.3 ft Impact of external force.
Run Over Load: Tested that car can roll over charger nozzle 2 Times!

Materials
Case Material: Thermo plastic,flame retardant grade UL94-0
Contact Pin: Copper alloy, silver + thermo plastic on the top
Sealing gasket: rubber or silicon rubber

Control Box
Leakage protection(Restart recover)
Over-voltage under-voltage protection (self-checking recover)
Overload protection (self-checking recover)
Lightning and surge protection

One Year Manufactures Warranty

*requires dedicated dual 120 Volt 20 Amp circuit / NEMA 5-15R Receptacles.
Not every combination of 2 breakers works so you simply test with the momentary button to test the voltage.  If you get a green light, you are all set.  Every home, business, office, has the ability to make this work in the USA, Mexico, Canada, and Japan.  No electrician required.  Inspect breaker box to make sure you have 20 amp breakers.  Test the polarity with a polarity tester.  Try two outlets if you do not get a green light, just relocate one of the power cords until the light turns green when you hold down the voltage tester.
Just relocate on extension cord until you get a green light. Does not work on GFCI or LCI outlets. Each power cord must be plugged into 2 different phases.  This means you can optionally change the breaker locations in your breaker panel if you want to use the two closest outlets next to your car if they are not already on different phases.  If you have GFCI outlets, you will have to replacement with standard wall outlets before this charger will work. 

Video

Pictures

 

Optional

Electrical Outlet Receptacle Polarity Tester 3 wire 120 volt 20100823

Replaces both items below

	Electric Vehicle Charger EVSE 220-240v Level 2 Car Nema 6-20P Plug To J1772 EV Charging Station Duosida 20180613
	Power Joiner Level 2 Step Up Inverter Electric AC Converts Dual 20 amp 115 Volt outlets to 240 Volt 3 wire 20 amp Use [Reverse6-20R]

Additional Information

Understanding the differences between different types of electric charger cables.

PLEASE INSTALL A WHOLE HOME SURGE AND LIGHTNING ARRESTER PROTECTION TO PROTECT BOTH YOUR CHARGING CABLE AND THE CARS COMPUTER!
LIGHTNING STRIKES ARE NOT A MANUFACTURES DEFECT AND WILL NOT BE COVERED.  In the photo to the right, the round item below the box, on the left is the lightning arrester, the rectangular item on the right is the surge protector.  These can be installed under the main panel or in the panel (if you have room).
Photo shows lightning arrestor Delta LA302RG and Siemens FS140 whole home surge protector.  It does not have to be these brands.


Tips:  One customer wrote, "I plugged into different walls, not the same outlet, and it did not work."

Answer:  This is incorrect step / understanding.

In order to have the power supply box work, it must be plugged into different phases.

There are two phases of power in every home.

Half of all the outlets are on left phase, and the other half is on right phase.

You must land on one of each phase in order for the power supply to work.

This means if I just randomly select two outlets in a home, I could be plugged into:  two left side phases, 2 right side phases, or 1 of left + 1 right (correct use of power supply, depress phase locator button on the power supply box and will illuminate bright green on the phase locator light if you plugged in correctly.)

If you look at the breaker panel (photo to the right) and notice the column of breakers on the left side and then a column on the ride side.

The way a breaker box is wired is the top left breaker is left phase, the 2^nd from the top left strait down the left column is right phase, 3^rd down is left column is left phase, 4^th down is right phase.  These breakers alternate phase location all the way down each column.

The top right column of breakers works exactly the same way.  You have to land on one left phase and and one right phase to make this item work.  It is OK to have landed on a pair of outlets that is left and right side and each is positioned anywhere in the breaker panel.

Since this power supply box will not work with GFCI or LCI outlets you can also replace a GFCI outlet with a standard wall receptacle.  

Optionally, if the two breakers you want to use are on the same phase, simply change the location of one of the two breakers to be in a different position in the column.   This is very easy to do and only takes a screw driver (see video link below.)  Go outside and turn off the breaker and turn off the breaker that is labeled as ‘main.’  Go back to the garage and take off the garage panel cover.  Grab the breaker you want to relocate and simply switch positions with another breaker either one up or one down in the column.   You can change the location of the breaker or change the location of the wire in the breaker (your choice.)  This will put the breaker on a different phase.  Again, see video below on how to do this.

https://youtu.be/BG9I-PokSdI?si=m06267ZWR54Tiknu

and
https://youtu.be/IzTV9t7bnH8?si=p1lgRxxO5gsEvmub

Once you are on different phases, and press the momentary phase location button on your power supply box, the green light will be bright green telling you, you selected one left and one right phase and you are good to use this power supply box below the required amp draw of the wall outlets you plugged into.