|
|
Therma-Stor Dehumidifiers
 Therma-Stor provides innovative
residential, light commercial, water damage restoration dehumidification, air scrubbing
and ventilation solutions, heat recovery water heaters, ventilation systems, and indoor
air quality products.
Residential and Light Commercial Dehumidifiers
|
The Santa Fe is a high efficiency residential dehumidifier that utilizes
refrigeration to cool the incoming air stream below its dew point as it
passes through the dehumidification (evaporator) coil. This cooling results
in the removal of moisture (latent heat) and reduction of the temperature
(sensible heat). The cooled and dried air is used to pre-cool the incoming
air stream resulting in up to a 200 percent increase in overall efficiency.
After the pre-cooling stage the processed air is reheated by passing through
the condenser coil. The latent heat removed by the evaporator coil is returned
to the air stream at this stage as sensible heat, resulting in an overall
increase in temperature from the incoming air.
Controlled by a dehumidistat with positive “ON” and “OFF” settings
Santa Fe has a built-in defrost system that is designed to 55°F.
Unit contains a blower switch
The Santa Fe is portable and provided with four casters.
The unit contains a six foot vinyl, gravity drain hose.
Wiring of the unit is installed six foot power cord; 115 volt
Power 6.8 amps
Intake Air 70°F/60% | 80°F/60%
Water Removal 85 lbs / 24 hours | 104 lbs / 24 hours
Pints/KWH 5.3 6.8
Width 20" 25"
Height 36" 41"
Depth 17" 24"
Weight 110 lbs 125 lb
|
Quote Me | Our Prices |
|
|
|
|
The Santa Fe Rx Air Purifying Dehumidifier is a free-standing device that
has been specially designed to provide quieter operation and a finished
appearance, making it suitable for use in offices, residences, libraries
and schools. An optional HEPA or Activated Carbon filtration systems are available.
The standard air filtration is provided by a pleated polyester and cotton blend media
filter located at the air intake at the top of the unit. The efficiency rating of this
filter is 40% in the ASHRAE 52-76 Dust Spot Test.
The optional HEPA filter is a micro-glass paper mini-pleat filter located in a special
housing mounted on the back of the Santa Fe Rx cabinet. The efficiency rating of this
filter is 99.97% on the D.O.P. test.
The Santa Fe Rx is controlled by a dehumidistat with positive “ON” and “OFF” settings
and a variable setting range from “20%” to “80%”.
The Santa Fe Rx has a built-in defrost system that is designed for operation down to 55F.
Power 6.3 amps
Intake Air 70°F/60% | 70°F/60%
Pints/KWH 5.0 / 5.3
Width 24" 24"
Height 37.375" HEPA 37.375"
Depth 18.125" HEPA 25.625"
Water Removal 73 lbs / 24 hours | 90 lbs / 24 hours
|
Quote Me | Our Prices |
|
|
|
The Ultra-Aire APD 100V ensures air filtration, fresh air ventilation and
humidity control. It provides a measured amount of fresh air into the home,
which is mixed with indoor air. The air is then filtered to remove airborne
particles and dehumidified to ensure the relative humidity in the home remains
below 50%.
Fresh Air Ventilation: Outdoor air is ducted to the unit via 6" round duct.
This provides necessary air changes to dilute pollutants and maintain high
oxygen content in the air. The amount of fresh air ventilation can be regulated
by a variety of controls.
Air Filtration: A measured amount of outdoor air is combined with indoor air
and passes through the filter chamber. A 30% efficient (ASHRAE Dust spot test)
media filter is standard. An optional 95% efficient (ASHRAE Dust spot test)
pleated media filter is available. If the optional filter is selected, the
standard filter operates as a pre-filter.
Dehumidification: High efficiency dehumidifier that utilizes refrigeration
to cool the incoming air stream below its dew point as it passes through the
dehumidification (evaporator) coil. This cooling results in the the removal
of moisture (latent heat) and reduction in temperature (sensible heat). The
cooled and dried air is used to pre-cool the incoming air stream resulting in
up to a 200 percent increase in overall efficiency. After the pre-cooling stage
the processed air is reheated by passing through the condenser coil. The latent
heat removed by the evaporator coil is returned to the air stream as sensible
heat, which results in an overall temperature increase from the incoming air.
Features: The unit is controlled by a 24 volt remote control panel. The standard
control contains a fan/filter switch that allows continuous air circulation
independent of dehumidification. The panel also contains a dehumidistat with
settings from 20 to 80 percent and positive "on" and "off" settings. The optional
Ultra-Aire control also contains a timer that activates a motorized damper to
provide programmed fresh air ventilation periods.
The unit is provided with 6 inch (fresh air) and 8 inch (indoor air) inlet collars.
The processed air exits the unit via an 8 inch round duct.
The condensed moisture is gravity drained from the unit by a 6 foot vinyl hose.
The unit is powered through a factory installed ten foot power cord; 115 volt with ground.
Power 6.8 amps
Water Removal 100 pints/day (80F, 60%)
Blower 220 CFM (.1 IWFG)
Filter Efficiency 30% std., 95% opt.; (ASHRAE Dust spot)
Width 21" 30"
Height 42" 47"
Depth 17" 25"
Weight 119 lb 134 lb
|
Quote Me | Our Prices |
|
|
|
The Ultra-Aire Air Purifying Dehumidifier ensures air filtration, fresh air
ventilation and humidity control. It provides a measured amount of fresh air
into the home, which is mixed with indoor air. The air is then filtered to
remove airborne particles and dehumidified to ensure the relative humidity
in the home remains below 50%.
Fresh Air Ventilation: Outdoor air is ducted to the Ultra-Aire APD 150H via 6"
round duct. This provides the necessary air changes to dilute pollutants and
maintain high oxygen content in the air. The amount of fresh air ventilation
can be regulated by a variety of controls.
Air Filtration: A measured amount of fresh air is combined with indoor air
and passes through the filter chamber. A 30% efficient (ASHRAE Dust spot test)
media is standard. An optional second stage 95% efficient (ASHRAE Dust spot test)
deep pleated media filter is available. If the optional filter is selected the
standard filter operates as a pre-filter.
Dehumidification: The Ultra-Aire APD 150H utilizes refrigeration to cool the
incoming air stream below its dew point as it passes through the dehumidification
(evaporator) coil. This cooling results in the the removal of moisture (latent heat)
and reduction in temperature (sensible heat). The cooled and dried air is used to
pre-cool the incoming air stream resulting in up to a 200 percent increase in
overall efficiency. After the pre-cooling stage the processed air is reheated
by passing through the condenser coil. The latent heat removed by the evaporator
coil is returned to the air stream as sensible heat, resulting in an overall
temperature increase from the incoming air.
The unit is controlled by a 24 volt remote control panel. The standard control
contains a fan/filter switch that allows continuous air circulation independent
of dehumidification. The panel also contains an adjustable dehumidistat with
positive "on" and "off" settings. The optional control panel contains a programmable
timer that activates a motorized damper and activates the blower to provide scheduled
fresh air ventilation.
The unit is provided with 6 inch (fresh air) and 10 inch (indoor air) inlet collars.
The processed air exits the unit via a 10 inch round duct.
The condensed moisture is gravity drained from the unit via a .56" ID x 8' vinyl hose.
The unit is powered through a factory installed 7.5 foot power cord; 115 volt with ground.
Power 12 amps
Water Removal 140 pints/day (80F, 60%)
Blower 400 CFM @ .0 IWG. (290 CFM @ .4 IWG.)
Filter Efficiency 30% std., 95% opt.; (ASHRAE Dust spot)
Width 46" 50"
Height 20.5" 29"
Depth 25" 29"
Weight 145 lb 220 lb
|
Quote Me | Our Prices |
|
|
Commerical Dehumidifiers
|
The HI-E Dry 100 high efficiency dehumidifier utilizes refrigeration to cool
the incoming air stream below its dewpoint as it passes through the dehumidification
(evaporator) coil. This cooling results in the removal of moisture (latent heat).
The cooled and dried air is used to pre-cool the incoming air stream resulting in
up to a 200 percent increase in overall efficiency. After the pre-cooling stage the
processed air is reheated by passing through the condenser coil. The latent heat
removed by the evaporator coil is returned to the air stream at this stagesulting in an overall temperature increase from the incoming air.
Controlled by a dehumidistat with settings from 20 to 80 percent relative humidity and a positive "on" and "off" setting.
Contains a blower switch that permits continuous blower operation independent of dehumidification.
Portable and provided with four casters.
Contains an internal condensate pump capable of lifting condensate 20 feet.
20 feet of condensate hose.
Factory installed six foot power cord, 115 volt with ground.
Power 6.8 amps
Blower 255 CFM
Width 20" 25"
Height 36" 41"
Depth 17" 24"
Weight 110 lbs 125 lbs
Intake Air 70F, 60% 80F, 60%
Water Removal (per day) 86 lbs 110lbs
Pints/KWH 6.0 6.8
|
Quote Me | Our Prices |
|
|
|
HI-E DRY dehumidifiers control damaging moisture and humidity in a wide
range of commercial and industrial applications. It reduces the relative
humidity of inlet air with a dewpoint above 35F. The ability to function
effectively in lower temperatures is built into every HI-E DRY dehumidifier.
Controlled by a dehumidistat with settings from 20 to 80 percent relative humidity and a positive "on" and "off" setting.
Contains a blower switch that permits continuous blower operation independent of dehumidification.
Portable and provided with four casters.
Contains an internal condensate pump capable of lifting condensate 20 feet.
20 feet of condensate hose.
Factory installed six foot power cord, 115 volt power cord, 115 volt with ground.
Power 12 amps (std.)
Blower 540 CFM
Width 36.6" 39.25"
Height 42" 48.75"
Depth 19" 30"
Weight 175 lbs 214 lbs
Intake Air 70F, 60% 80F, 60%
Water Removal (per day) 143 lbs 190 lbs
Pints/KWH 5.0 5.9
|
Quote Me | Our Prices |
|
|
Restoration and Construction Dehumidifiers
|
The Phoenix 200 MAX removes more water and has more grain depression
than other refrigerant dehumidifiers while requiring less than 7.5 amps
of electricity. Combined with this performance, the multiple ducting and
air filtration options makes the Phoenix 200 MAX the most effective and
versatile drying device made.
The Phoenix 200 MAX features the hallmarks of the Phoenix line: stainless
steel cabinet, shock-absorbing axle, internal pump with 30 feet of hose,
and a 5-year warranty.
Standard 2" Pleated Media 30% MERV-6
Optional 2" Pleated Media 57% MERV-8
Optional 4" Mini-Pleat Media 95% MERV-14
Warranty 5- Years
1st year 100% of Parts and Labor
2nd-5th year 100% of Parts of sealed refrigeration system.
Width 20" 24.25" 27.5"
Height 40" 40" 45.5"
Depth 18.25" 21.375" 22"
Weight 131 lb 160 lb
|
Quote Me | Our Prices |
|
|
|
The design goal of the Phoenix 300 was to build a dehumidifier that would
maximize the water removal capacity from a single 110 volt, 15 amp circuit.
In order to be a viable product, we had to house this high capacity dehumidifier
in a portable cabinet of manageable size and weight. We also kept in mind the
fine reputation the Phoenix 200 had earned, and knew that the 300 would have to
be able to live up the Phoenix name. We hope you are not only pleased, but amazed
at the performance of the Phoenix 300.
Power 115 volt, 12 amps
Water Removal
176 pints/day @ AHAM (80°F, 60%RH)
304 pints/day maximum (90°F, 90%RH)
Blower 540 CFM
Operating Range 33°F to 105°F
Warranty 5- Years
1st year 100% of Parts and Labor
2nd-5th year 100% of Parts of sealed refrigeration system.
Width 24" 29" 30"
Height 45" 46" 54"
Depth 20" 25" 28"
Weight 175 lb 210 lb
|
Quote Me | Our Prices |
|
|
|
|