ReverseL6-30R for only $381.93 - Steambrite's price on the Electrical Adapter Temporary Power Boxes - ReverseL6-30R extractor, Equipmentcarpet cleaning equipment, Equipment flood restoration, Equipment carpet cleaning machine,

Power Cord Adapter Inverter (Reverse Converter) Takes two 115-120 volt outlets and allows you to use 230-240 volt appliances that uses under 20 amps @ 230-240 volts (4800 watts) current to NEMA L6-30R single phase receptacle.  Commonly used with most Electric Cars, Concrete Vacuum Systems, Electric Pressure Washers, Barco Large Venue Projectors, and Sawstop, Floor and Stroke Wood Sanders, Three Spindle Shapers, Gearhead Lathes, and many Plasma Cutters.  Fast and easy 240 volts.

   

mps @ 240 volts and you are plugged into 20 amp 120 volt outlets, you will need to turn the pressure down to lower the amp draw.  Just turn the pressure regulator / unloader knob counter clockwise.  The less pressure, the less horse power is needed to turn the electric motor and this will lower the amp draw.  

 

 Until both 120 volt power cords are connected to a 120 volt electrical source, it is electrically isolated from the electrical circuit of the non plugged in side on the 2nd power cord.  This protects the user from accidental shock through the plug contact.

 

Can also be used with:
Villo

Electrical Outlet Receptacle 20100823 Tester 3 wire 120 volt  This is to confirm your home or office was wired correctly.

Answer:  This is incorrect step / understanding.

In order to have the power supply box work, it must be plugged into different phases.

There are two phases of power in every home.

Half of all the outlets are on left phase, and the other half is on right phase.

You must land on one of each phase in order for the power supply to work.

This means if I just randomly select two outlets in a home, I could be plugged into:  two left side phases, 2 right side phases, or 1 of left + 1 right (correct use of power supply, depress phase locator button on the power supply box and will illuminate bright green on the phase locator light if you plugged in correctly.)

If you look at the breaker panel (photo to the right) and notice the column of breakers on the left side and then a column on the ride side.

The way a breaker box is wired is the top left breaker is left phase, the 2^nd from the top left strait down the left column is right phase, 3^rd down is left column is left phase, 4^th down is right phase.  These breakers alternate phase location all the way down each column.

The top right column of breakers works exactly the same way.  You have to land on one left phase and and one right phase to make this item work.  It is OK to have landed on a pair of outlets that is left and right side and each is positioned anywhere in the breaker panel.

Since this power supply box will not work with GFCI or LCI outlets you can also replace a GFCI outlet with a standard wall receptacle.  

Optionally, if the two breakers you want to use are on the same phase, simply change the location of one of the two breakers to be in a different position in the column.   This is very easy to do and only takes a screw driver (see video link below.)  Go outside and turn off the breaker and turn off the breaker that is labeled as ‘main.’  Go back to the garage and take off the garage panel cover.  Grab the breaker you want to relocate and simply switch positions with another breaker either one up or one down in the column.   You can change the location of the breaker or change the location of the wire in the breaker (your choice.)  This will put the breaker on a different phase.  Again, see video below on how to do this.

https://youtu.be/BG9I-PokSdI?si=m06267ZWR54Tiknu

CWP Productions uses these with their

Barco HDX-W20 FLEX (9012005) 20,000 Lumens, WUXGA, 3 Chip DLP projector

www.cwpproductions.com

Clean Storm HEPA Concrete Grinder Dust Slurry Extractor Collector Triple Vacuum Motors 5 Stage Filter System Wet/Dry Shop Vac 335CFM 20230111  Video On Link!