

Clean Storm 20141420, Hi-Flow 5 Micron Filter Element for Filter Housing
Description
The Clean Storm 20141420 Hi-Flow 5 Micron Filter Element is engineered for high-efficiency fluid filtration in pressure washer water reclaim systems and heavy-duty extraction setups. Constructed with a pleated polyester filtration medium supported by a rigid polypropylene core, this filter element provides maximum surface area to capture ultra-fine particulates down to 5 microns while maintaining optimal liquid flow. Designed for low-pressure operating environments up to 60 PSI, it ensures reliable sediment removal, extending the service life of downstream pumps, check valves, and high-pressure nozzles.
Features
- High-Efficiency 5 Micron Rating: Captures fine rust, sand, silt, scale, and suspended solids down to 5 microns to safeguard fluid systems.
- Pleated Polyester Media: Offers maximum surface area for increased dirt-holding capacity, reduced initial pressure drop, and extended service intervals.
- Durable Polypropylene Core: Provides internal structural support to prevent element collapse during high-flow operational cycles.
- High Flow Rate Capability: Engineered to support up to 10 GPM (gallons per minute) liquid throughput with minimal friction loss.
- Low-Pressure Performance: Optimized for low-pressure suction and transfer lines operating under 60 PSI.
- Multi-Stage Compatibility: Designed to work seamlessly in series with 20 micron and 50 micron elements for progressive step-down filtration.
Applications
- Pressure Washer Reclaim & Water Recycling Systems
- Truckmount Carpet Extraction Systems
- Commercial Pressure Washer Inlet Water Filtration
- Industrial Wash Water Recovery & Treatment Units
- Low-Pressure Fluid Transfer & Recirculation Lines
- Clean Storm High-Flow Filter Housings
Specifications
| Brand |
Clean Storm |
| Part Number |
20141420 |
| Filter Media Material |
Pleated Polyester |
| Inner Core Material |
Polypropylene |
| Micron Rating |
5 Micron |
| Maximum Flow Rate |
10 GPM (Gallons Per Minute) |
| Maximum Operating Pressure |
60 PSI |
| Application Environment |
Water Reclaim / Low-Pressure Filtration |
| Series Compatibility |
Clean Storm Water Reclaim Filter Housings |
Cross-Reference SKUs
| 20141420 |
| Clean Storm 20141420 |
| CleanStorm 20141420 |
| 20141420-5M |
| CS-20141420 |
| CS20141420 |
| 5M-10GPM-FE |
Tips and Additional Information
Multi-Stage Series Filtration Tip: For optimal system efficiency and maximum cartridge longevity, install filtration elements back-to-back in series using progressive step-down ratings. We recommend positioning a 50 Micron (12 GPM) filter element first to catch large debris, followed by a 20 Micron (10 GPM) element for intermediate filtration, and finishing with this 5 Micron (10 GPM) element for fine polishing. This staged approach prevents premature blinding of the fine 5-micron media and extends overall system runtime.
Pre-Installation Inspection & Maintenance: Always inspect the internal housing seals and O-rings prior to seating a new filter element. Ensure the filter cartridge sits squarely over the housing center post to prevent fluid bypass. Flush new elements briefly with clean water before placing the system into full service.
Frequently Asked Questions
Q: What is the pressure limit for the Clean Storm 20141420 filter element?
A: This filter element is designed for low-pressure filtration systems operating under 60 PSI. It should be installed on the inlet or suction side of high-pressure pumps, not on the high-pressure discharge line.
Q: Can I use this 5 micron element by itself without pre-filters?
A: While the 5 micron element can function independently, using it alone in heavily contaminated water reclaim applications will cause rapid clogging. Running a 50 micron and 20 micron filter upstream in series is highly recommended to trap heavier solids first.
Q: Is this filter cartridge compatible with standard Clean Storm reclaim filter housings?
A: Yes, the 20141420 element is fully compatible with the Clean Storm Filter Housing designed for pressure washer reclaim and water recovery operations.
Q: How do I know when it is time to replace the filter element?
A: Replace the element when a noticeable drop in flow rate occurs, when differential pressure across the housing rises, or when visual inspection reveals heavy particulate loading across the pleated media.
Warranty & Safety Information
Warranty Information: Clean Storm products are covered by a standard manufacturer defects warranty against flaws in material and workmanship when installed and operated under recommended conditions. Warranty coverage does not cover normal wear-and-tear, media blinding from improper pre-filtration, or damage resulting from misapplication.
Safety & Operational Rules: Do NOT exceed the maximum rated pressure of 60 PSI. Operating this filter element above recommended pressure limits can compromise the structural integrity of the core and media, leading to element collapse or housing failure. Never disconnect filter housings while the system is pressurized. Always relieve line pressure completely before performing filter inspections, cartridge changes, or maintenance.
Optional housing
|