

Clean Storm 20211232, Wall Mount Electric Cold Pressure Washer, Industrial Coated Frame, 3/8" x 50' Hose, 4 GPM, 2000 PSI, 5 HP 230V 1-Phase
Description
The Clean Storm 20211232 is a 4 GPM, 2000 PSI electric cold-water wall-mount pressure washer powered by a 5 HP, 230V, 26A single-phase motor with an open-frame design for bay cleaning. Built without a full cabinet enclosure to reduce upfront equipment costs while preserving commercial wash performance, this unit bolts securely to a reinforced wall to keep floor space clear. It pairs a totally enclosed, thermal-overload-protected industrial electric motor with an industrial triplex plunger pump featuring ceramic plungers, stainless steel valves, mechanical pump thermal protection, and an unloader valve. Complete with a 50-foot x 3/8-inch high-pressure hose, trigger gun, low-pressure chemical injection, and four Q-Meg spray nozzles, it arrives ready for stationary commercial wash bays.
Features
- Space-Saving Open Wall-Mount Frame: Economy open-frame architecture eliminates the cost of an outer shroud while mounting securely to reinforced facility walls to free up valuable floor space.
- Protective Industrial Frame Coating: Heavy-duty industrial coating shields the steel mounting chassis against moisture, detergent splash, and daily wash-bay wear.
- Integrated Hose, Gun & Nozzle Storage: Built-in lower frame hook neatly hangs the trigger gun, wand, and 50' x 3/8" hose assembly, while integrated frame grommets hold Q-Meg spray tips within easy reach.
- Totally Enclosed 5 HP Industrial Motor: Single-phase 230 Volt, 26 Amp electric motor features a totally enclosed housing with built-in thermal overload protection for dependable continuous duty.
- Commercial Triplex Plunger Pump: Engineered with wear-resistant ceramic plungers, corrosion-resistant stainless steel valves, mechanical thermal pump protection, and a pressure-regulating unloader valve.
- Low-Pressure Downstream Chemical Injection: Draws concentrated liquid detergents automatically when the low-pressure soap nozzle is installed, simplifying pre-soak and degreasing workflows.
- Complete Spray Accessory Package: Ships with a 50' x 3/8" high-pressure hose, trigger spray gun, 10-foot power cord, and 0°, 15°, 25°, and 40° quick-connect Q-Meg spray nozzles.
Applications
- Automotive Dealership & Fleet Wash Bays: Stationary wall-mounted cold-water washing for cars, vans, delivery trucks, and municipal fleet vehicles.
- Equipment Rental & Heavy Machinery Yards: Routine mud, grease, and grime removal on skid steers, excavators, agricultural implements, and construction tools.
- Manufacturing Plants & Maintenance Shops: Fixed wash-down stations for production machinery, parts bays, loading docks, and shop floors.
- Commercial Car Washes & Detail Centers: Dedicated prep bay pressure washing and detergent application where floor space must remain unobstructed.
- Food Processing & Warehouse Sanitation: Cold-water facility washdowns and crate/tote cleaning in ventilated indoor wash rooms.
Specifications
| Brand |
Clean Storm |
| Model / Primary Part Number |
20211232 (Alternate Spec Sheet Reference: 2021132) |
| Equipment Type |
Wall-Mount Electric Cold-Water Pressure Washer (Economy Open Frame / No Cover) |
| Water Temperature Type |
Cold Water (Max Pump Inlet Water Temp: 160° F / 71° C) |
| Flow Rate |
4.0 GPM (15.2 LPM) |
| Rated / Operating Pressure |
2000 PSI (138 Bar) Nominal Rating; 3000 PSI (276 Bar) Spec Sheet Pump/System Rating |
| Motor Horsepower |
5 HP |
| Electrical Requirements |
230 Volt / 26 Amp / 1-Phase (Single Phase) |
| Motor Protection |
Totally Enclosed Industrial Motor with Thermal Overload Protection |
| Pump Design & Materials |
Industrial Triplex Plunger Pump with Ceramic Plungers & Stainless Steel Valves |
| Pump Protection |
Unloader Valve & Mechanical Thermal Relief Protection |
| Chemical Injection |
Low-Pressure Concentrate Liquid Detergent Injection (Soap-Tip Activated) |
| Frame Construction & Finish |
Wall-Mount Steel Frame with Industrial Protective Coating, Hose/Gun Hook & Nozzle Grommets |
| High-Pressure Hose & Port Size |
50' Length x 3/8" ID Hose (Standard 3/8" NPTF / Quick-Connect High-Pressure Discharge) |
| Swivel / Fitting Mechanics |
Non-Live Fixed Installation Threads (NPTF Tapered Pipe Threads & Quick-Connect Couplers; Use Live Swivel at Gun Inlet if Continuous Hose Rotation Is Desired) |
| Included Nozzles |
0°, 15°, 25°, and 40° Q-Meg Quick-Connect Tips |
| Power Cord Length |
10 Feet |
| Overall Dimensions (L x W x H) |
28" x 22" x 30" |
| Shipping Weight |
300 lbs |
Cross-Reference SKUs
| Clean Storm 20211232 |
| 20211232 |
| Clean Storm 2021132 |
| 2021132 |
| CS-20211232 |
| CS20211232 |
| Clean Storm 20220129 (Covered Stainless Steel Equivalent – 2000 PSI, 4 GPM, 230V/240V 1-Phase, 26A, 5 HP) |
| Northern Tool 104216 (Covered Frame OEM Reference Equivalent) |
| Clean Storm 20211233 (3-Phase Equivalent – 2000 PSI, 4 GPM, 230V 3-Phase) |
| Clean Storm 20211231 (3000 PSI 1-Phase Open-Frame Upgrade – 4 GPM, 7.5 HP, 34A) |
Tips and Additional Information
Structural Wall Mounting & Alignment: Because the Clean Storm 20211232 has a shipping weight of 300 lbs and generates high mechanical torque during startup, mount the frame only to a structurally reinforced concrete, masonry, or heavy-gauge steel-backed wall using grade-rated anchor fasteners. Level the frame horizontally so the triplex pump crankcase oil bath remains flat and all plungers receive uniform lubrication.
Proper Thread Sealing Practices: When connecting the water supply line, pressure gauge, unloader fittings, or replacement 3/8" NPTF tapered pipe threads, apply high-density PTFE thread seal tape (3 to 4 wraps clockwise) or pressure-rated anaerobic pipe sealant to male tapered threads only. Never apply thread tape to straight mechanical threads (such as NPSM swivel nuts or garden hose GHT fittings) or O-ring boss seals, as these seal via mechanical flare/gasket compression and tape can cause leaks or debris contamination in stainless steel pump valves.
Live vs. Non-Live Swivel Operation: Standard stationary plumbing connections on the pump discharge and wall frame are non-live installation fittings designed strictly for static alignment during assembly—never allow rigid pipe joints to rotate under pressure. For tangle-free wand movement during washing, verify that the trigger gun inlet features a live high-pressure rotary swivel rated above 3000 PSI and 160° F, and avoid dragging non-swiveling hose couplings across concrete floors.
Pre-Installation Inspection & Startup Guidelines: Before energizing the 230V, 26A single-phase circuit, verify incoming supply voltage under load, confirm dedicated breaker sizing with a licensed electrician, and replace any solid shipping oil plug on the pump crankcase with the vented dipstick/breather cap. Flush the cold-water supply line to clear scale or sediment, purge air from the pump and 50' x 3/8" hose with the nozzle removed, and confirm adequate inlet water flow (minimum 4.5–5.0 GPM supply) to prevent pump cavitation.
Frequently Asked Questions
Q: Why is the Clean Storm 20211232 labeled an economy model, and how does it differ from covered models?
A: It is designated an economy model solely because it omits the outer stainless steel shroud/cover to lower purchase cost. It retains the same heavy-duty 5 HP totally enclosed industrial motor, ceramic-plunger triplex pump, unloader valve, and commercial spray accessories as covered Clean Storm units.
Q: What electrical service is required to run this pressure washer?
A: The unit requires a dedicated 230 Volt, single-phase (1-Phase) electrical supply rated for at least 26 running amps (typically installed on a dedicated 35A–40A two-pole circuit breaker per local electrical code) and includes a 10-foot power cord.
Q: Are the pressure fittings live rotary swivels or non-live installation fittings?
A: The pump manifold, unloader, and frame bulkhead ports use non-live NPTF tapered threads intended strictly for static installation alignment. Quick-connect couplers on the 50' x 3/8" hose allow static repositioning when depressurized, whereas continuous rotation during spraying requires a dedicated live high-pressure rotary swivel at the spray gun inlet.
Q: How do I seal the 3/8" high-pressure hose and inlet water connections?
A: Use PTFE thread tape or liquid pipe thread sealant exclusively on tapered male NPTF threads (such as 3/8" NPT hose ends or pump manifold adapters). Do not tape straight mechanical swivel nuts (NPSM) or rubber-washer garden hose inlet fittings, as those rely on gasket or metal-to-metal seat compression.
Q: Why does the title list 2000 PSI while the specification sheet lists 3000 PSI operating pressure?
A: The Clean Storm 20211232 is configured and motor-matched with a 5 HP 230V single-phase motor to deliver a continuous duty rating of 2000 PSI at 4.0 GPM, while utilizing a heavy-duty commercial triplex pump assembly rated up to 3000 PSI (276 Bar) for extended mechanical longevity and safety margin.
Q: Can I feed hot water into this cold-water wall-mount pressure washer?
A: This is a cold-water machine without a burner; however, its industrial triplex pump and mechanical thermal protection can accept pre-heated inlet water up to a maximum temperature of 160° F (71° C). Exceeding 160° F will damage pump seals and void coverage.
Warranty & Safety Information
Manufacturer Warranty Coverage: Clean Storm commercial wall-mount pressure washers are backed by manufacturer coverage against defects in materials and workmanship under normal commercial use—covering the industrial electric motor, triplex plunger pump assembly, and coated steel mounting frame. Wear items such as spray nozzles, O-rings, pump packings/seals, check valves, trigger guns, and high-pressure hoses are covered only for initial manufacturing defects upon receipt.
Conditions That Void Warranty:
- Operating the machine above its rated pressure limits or feeding inlet water hotter than 160° F (71° C).
- Running the pump dry, restricting inlet water supply below 4 GPM, or leaving the unit in bypass mode with the trigger closed long enough to overheat the pump.
- Connecting the motor to improper voltage, undersized wiring, or incorrect phase power, or exposing the open-frame unit to direct high-pressure overspray.
- Using non-live tapered fittings in continuous rotary service, over-torquing NPTF ports, or introducing thread tape/debris into pump valves.
- Freeze damage caused by failing to winterize or drain water from the pump, hose, and unloader in sub-freezing temperatures.
Critical Operational Safety Warnings: Never disconnect high-pressure hoses, quick couplers, or nozzles while the system is pressurized—always shut off power and squeeze the trigger gun to bleed residual line pressure first. High-pressure fluid injection can cause severe personal injury; never point the spray wand at people, animals, or electrical panels, and always wear ANSI-approved eye protection and slip-resistant footwear during operation.
|