

Clean Storm 20220114 Wall Mounted Cold Water Electric Pressure Washer 1500 PSI 2.2 GPM 120V 20A Stainless Steel
Description
Delivering 1500 PSI at 2.2 GPM, the Clean Storm 20220114 Wall Mounted Cold Water Electric Pressure Washer provides space-saving commercial cleaning with Auto Stop and Start functionality. Proven over 25 years in demanding facilities, this unit features a full stainless steel frame and protective cover engineered to withstand harsh washdown environments. The slide-in wall mounting bracket secures permanently to a reinforced wall for rapid installation and serviceability. Equipped with a totally enclosed, thermal overload-protected 2 HP industrial electric motor and an industrial triplex plunger pump with ceramic plungers and stainless steel valves, this system ensures continuous reliability. Integrated storage hooks hold the 50' x 3/8" hose and trigger gun, while cover grommets organize the included 0°, 15°, 25°, and 40° Q-Meg nozzles. A dual chemical metering valve allows operators to switch between two liquid concentrates and adjust dilution ratios effortlessly using low-pressure soap tip injection.
Features
- Full stainless steel frame and protective cover prevent rust and corrosion in wet, high-humidity wash bays.
- Auto Stop and Start system shuts down the motor when the trigger gun is released to reduce pump wear and energy consumption.
- Industrial triplex plunger pump built with solid ceramic plungers, stainless steel valves, and an integrated unloader valve for pressure regulation.
- 2 HP totally enclosed industrial electric motor features built-in thermal overload protection for continuous commercial duty.
- Dual chemical injection valve allows instant selection between two concentrate detergents with precision proportion control.
- Slide-on wall mounting plate locks onto reinforced wall structures while allowing fast frame removal for maintenance.
- Integrated frame hooks and cover grommets keep the 50' high-pressure hose, trigger gun, and Q-Meg spray tips organized off the floor.
- 35' heavy-duty power cord includes an inline GFCI plug for operator electrical safety in wet locations.
Applications
- Automotive detailing bays, car washes, and dealership service centers
- Commercial kitchens, food processing plants, and sanitation washdown rooms
- Fleet maintenance garages, municipal transit depots, and equipment rental facilities
- Manufacturing floors, warehouses, and industrial processing areas
- Agricultural barns, dairy parlors, and veterinary clinics
Specifications
| Brand |
Clean Storm |
| Part Number |
20220114 |
| Mounting Type |
Wall Mount with Slide-In Bracket |
| Frame Material |
Stainless Steel with Protective Cover |
| Operating Pressure |
1500 PSI (103.5 Bar) |
| Flow Rate |
2.2 GPM (8.4 LPM) |
| Motor Horsepower |
2 HP Totally Enclosed Industrial |
| Electrical Requirements |
120 Volt, 20 Amp, Single Phase |
| Power Cord |
35' with Inline GFCI |
| Pump Design |
Industrial Triplex Plunger with Ceramic Plungers & Stainless Steel Valves |
| Pump Thermal Protection |
Mechanical |
| Max Pump Inlet Water Temp |
160° F |
| Control Feature |
Auto Stop and Start with Unloader Valve |
| Chemical Injection |
Dual Valve Low-Pressure Metering System |
| Hose Dimensions |
50' x 3/8" High-Pressure Hose |
| Included Nozzles |
0°, 15°, 25°, 40° Q-Meg Tips & Soap Tip |
| Product Dimensions |
23" x 16" x 31" |
| Shipping Weight |
165 lbs |
Cross-Reference SKUs
| 20220114 |
| CS-20220114 |
| CS20220114 |
| CLEANSTORM-20220114 |
| CLEANSTORM20220114 |
Tips and Additional Information
Pre-Install Inspection & Wall Mounting: Before mounting, verify that the wall structure can support the 165 lb unit weight plus dynamic operating vibration and hose pull forces. Anchor the mounting plate into solid masonry, concrete, or structural framing before sliding the stainless steel frame onto the bracket.
Thread Sealing & Hose Alignment: Apply PTFE thread seal tape or hydraulic thread sealant to all non-swivel NPT pipe threads on water inlet and high-pressure discharge connections. Ensure the 50' x 3/8" hose uses a swivel connection at the trigger gun to prevent hose kinking and wrist fatigue during operation; avoid over-tightening brass or stainless fittings to prevent thread galling.
Electrical & Water Supply Setup: Connect the 35' GFCI power cord directly to a dedicated 120V, 20A grounded receptacle—do not use undersized extension cords that cause voltage drop and motor overheating. Flush the incoming water supply line prior to connection to clear debris that could damage the triplex pump valves.
Frequently Asked Questions
Q: How does the Auto Stop and Start feature operate on the Clean Storm 20220114?
A: When the operator releases the trigger gun, pressure builds inside the discharge line and signals the switch to shut off the 2 HP electric motor automatically. Squeezing the trigger drops system pressure and immediately restarts the motor, preventing bypass overheating and extending pump seal life.
Q: How do I switch between the two chemical detergents?
A: Install the low-pressure soap nozzle onto the trigger gun wand, then turn the dual chemical metering valve knob on the unit to select Chemical A, Chemical B, or Off, and dial in your desired detergent dilution ratio.
Q: Can I feed hot water into this cold water pressure washer?
A: Yes, while this unit does not have an onboard burner, its triplex plunger pump is rated for a maximum inlet water temperature of 160° F, allowing connection to a facility hot water supply line.
Warranty & Safety Information
Warranty Coverage: Backed by the manufacturer's standard commercial warranty covering defects in materials and workmanship on the stainless steel frame, electric motor, and triplex pump. Warranty coverage is voided by running the pump dry, exceeding the 160° F maximum inlet water temperature, operating on improper voltage or amperage circuits, or failing to protect the pump from freezing temperatures.
Safety Hazards & Operating Limits: Do not exceed the maximum operating pressure of 1500 PSI or inlet water temperature of 160° F. High-pressure fluid streams can cause severe injection injuries; never point the trigger gun at people, animals, or electrical equipment. Always test the inline GFCI plug before each use, wear ANSI-approved eye and hearing protection, and relieve residual system pressure before disconnecting hoses or nozzles.
|