

Clean Storm 20220160, Skid Cold Water Pressure Washer 2500 PSI 3 GPM Honda 196cc Gas Engine Steel Frame
Description
The Clean Storm 20220160 is a commercial skid-mounted cold water pressure washer delivering 2500 PSI at 3 GPM via a Honda 196cc gas engine and industrial triplex plunger pump. Engineered for mobile installation in utility trailers, pickup truck beds, or van side doors, this heavy-duty unit connects directly to a standard garden hose supply. Built on an industrial-coated tube and plate steel frame, it integrates a ceramic plunger pump with stainless steel valves, low-pressure chemical injection, an unloader valve with fresh water tank recirculation for pump cooling, and a secondary pressure pop-off valve for continuous commercial operation.
Features
- Industrial Honda 196cc recoil-start gas engine with a 1.9-quart fuel tank delivers reliable commercial power without requiring electrical hookups.
- Heavy-duty triplex plunger pump constructed with wear-resistant ceramic plungers and corrosion-resistant stainless steel valves for extended service life.
- Integrated unloader valve recirculates bypass water back to the fresh water tank, providing mechanical thermal protection to prevent pump overheating.
- Secondary pressure pop-off relief valve protects internal pump seals and plumbing from destructive over-pressurization spikes.
- Industrial-coated tube and plate steel skid frame resists rust, vibration, and harsh outdoor job-site environments.
- Low-pressure downstream chemical injection system allows seamless switching between detergent application and high-pressure rinsing directly from the heavy-duty trigger gun and wand.
- Includes a 50-foot x 3/8-inch high-pressure discharge hose and five quick-connect nozzles (0°, 15°, 25°, 40°, and soap/detergent).
Applications
- Mobile commercial pressure washing rigs mounted inside van side doors, pickup truck beds, or open utility trailers.
- Fleet washing and heavy equipment degreasing for construction, agricultural, and municipal vehicles.
- Concrete flatwork, driveway, sidewalk, and parking lot surface cleaning using standard garden hose water connections.
- Building exterior washing, roof prep, deck restoration, and industrial facility maintenance.
Specifications
| Brand |
Clean Storm |
| Part Number / Model |
20220160 |
| Water Temperature Type |
Cold Water |
| Mounting Configuration |
Skid Mount |
| Operating Pressure |
2500 PSI |
| Flow Rate |
3.0 GPM |
| Engine Manufacturer |
Honda |
| Engine Displacement |
196cc |
| Starting System |
Recoil Pull Start |
| Fuel Tank Capacity |
1.9 Quarts |
| Pump Type |
Triplex Plunger Pump (Ceramic Plungers, Stainless Steel Valves) |
| Pump Thermal Protection |
Mechanical (Unloader Bypass Recirculation) |
| Maximum Inlet Water Temperature |
160°F |
| Chemical Injection |
Low-Pressure Downstream Injector |
| Safety Relief |
Unloader Valve and Secondary Pressure Pop-Off Valve |
| Frame Material & Finish |
Industrial Coated Tube and Plate Steel |
| Discharge Hose |
50' x 3/8" High-Pressure Hose (Quick-Connect / NPT Fittings) |
| Inlet Connection |
Standard Garden Hose Thread (3/4" GHT) |
| Included Nozzles |
Quick-Change 0°, 15°, 25°, 40°, and Detergent Nozzles (1/4" QC) |
| Overall Dimensions (L x W x H) |
84" x 60" x 56" |
| Shipping Weight |
500 lbs |
Cross-Reference SKUs
| 20220160 |
| CS-20220160 |
| CS20220160 |
| CLEANSTORM-20220160 |
| CLEANSTORM20220160 |
Tips and Additional Information
Before initial startup, inspect engine crankcase oil and pump oil levels, verify that the shipping breather plug on the pump is replaced with the vented dipstick, and ensure all threaded NPT and quick-connect fittings are properly sealed with PTFE thread tape or pipe dope to prevent pressure loss. When mounting the skid frame onto a truck bed, van floor, or trailer, align the base frame evenly over structural crossmembers and secure with Grade 5 or Grade 8 mounting hardware and vibration-dampening washers. Note that standard trigger guns and hose connections are non-live; install an optional high-pressure live swivel at the gun inlet if continuous 360-degree hose rotation under pressure is desired. Always flush clean water through the chemical injector after each use to prevent detergent crystallization inside the check valve.
Frequently Asked Questions
Q: Can this pressure washer draw water from a buffer tank or only a pressurized garden hose?
The unit is configured to connect to a standard pressurized garden hose supply and features an unloader bypass line that recirculates water to keep the pump cool during trigger release. If feeding from a non-pressurized buffer tank, ensure adequate gravity-feed head pressure and an oversized suction line with an inline mesh strainer to prevent pump cavitation.
Q: How does the mechanical thermal protection prevent pump damage?
When the trigger gun is released while the Honda 196cc engine is running, the unloader valve diverts bypassed water back into the fresh water recirculation loop rather than trapping heated water inside the pump manifold, keeping seal and plunger temperatures safely below the 160°F maximum limit.
Q: How do I switch between high-pressure washing and applying detergent?
Insert the low-pressure soap/detergent quick-change nozzle into the 1/4" quick-connect coupler at the end of the wand. The drop in line pressure automatically activates the downstream chemical injector to draw soap into the water stream.
Warranty & Safety Information
Covered by manufacturer limited warranty against defects in materials and workmanship; Honda engine warranty is administered separately through authorized Honda service centers. Warranty coverage is voided by running the pump dry, exceeding the 160°F maximum inlet water temperature, freezing water inside the pump manifold, altering factory unloader pressure settings above 2500 PSI, or operating without proper oil levels. Always operate in a well-ventilated outdoor area to prevent carbon monoxide accumulation from engine exhaust, wear ANSI-approved eye and hearing protection, never point the high-pressure spray stream at people or animals, and relieve residual line pressure before disconnecting hoses or nozzles.
|