

Clean Storm 20220180, Stationary Hot Water Pressure Washer 8 GPM 2000 PSI LP Gas Fired 230V 10 HP Industrial Coated Steel
Description
The Clean Storm 20220180 Stationary Hot Water Pressure Washer delivers 8 GPM at 2000 PSI using an LP gas fired forced air burner and a 10 HP 230V electric motor for continuous industrial cleaning. Designed for permanent bay installation, this heavy-duty skid unit connects directly to a 1-inch LP gas supply line and features a Schedule 80 heating coil wrapped in stainless steel to heat water up to 195° F. Built on an industrial-coated steel tubing frame, it pairs an industrial triplex plunger pump with ceramic plungers and stainless steel valves to handle demanding commercial washdown operations. Complete with a 50-foot 3/8-inch high-pressure hose, dual-wand trigger gun, low-pressure chemical injector, and four quick-change nozzles, this stationary system provides reliable high-volume thermal cleaning power for fixed wash bays and manufacturing facilities.
Features
- High-output 10 HP totally enclosed electric motor with built-in thermal overload protection for continuous duty cycles.
- Industrial triplex plunger pump engineered with wear-resistant ceramic plungers and corrosion-resistant stainless steel valves.
- Dual over-pressure protection utilizing a primary unloader valve and a secondary pressure pop-off relief valve.
- Heavy-duty Schedule 80 steel heating coil encased in a protective stainless steel wrap for maximum thermal retention and longevity.
- Forced-air LP gas burner system regulated by an adjustable thermostat and high-temperature limit switch rated up to 195° F.
- Industrial-coated steel tubing skid frame built to withstand harsh wash-bay moisture and chemical exposure.
- Downstream low-pressure chemical injection system for applying concentrated liquid detergents and degreasers.
- Heavy-duty trigger gun paired with a dual wand and side-handle valve for instant switching between high-pressure rinse and soap application.
- Includes a 50-foot x 3/8-inch high-pressure discharge hose, 10-foot power cord, and 0°, 15°, 25°, and 40° quick-change spray nozzles.
Applications
- Permanent indoor or outdoor wash bays in commercial fleet maintenance and trucking terminals.
- Heavy equipment, construction machinery, and agricultural implement degreasing stations.
- Industrial manufacturing plants, food processing facilities, and municipal sanitation depots.
- Facility piping and multi-drop washdown systems utilizing fixed stationary hot water supply lines.
Specifications
| Brand |
Clean Storm |
| Model / Part Number |
20220180 |
| Mounting Configuration |
Stationary Skid Frame |
| Frame Material & Finish |
Industrial-Coated Steel Tubing |
| Operating Pressure |
2000 PSI |
| Flow Rate |
8 GPM (30.4 LPM) |
| Maximum Water Temperature |
195° F |
| Maximum Pump Inlet Water Temp |
140° F |
| Motor Horsepower |
10 HP (Totally Enclosed, Thermal Overload Protected) |
| Electrical Requirements |
230 Volt, 40 Amp, 1 Phase |
| Power Cord Length |
10 Feet |
| Pump Type & Internals |
Industrial Triplex Plunger Pump (Ceramic Plungers, Stainless Steel Valves) |
| Pump Thermal Protection |
Mechanical |
| Pressure Safety Controls |
Unloader Valve & Secondary Pressure Pop-Off |
| Burner Fuel Type |
LP Gas (Liquid Propane) |
| Gas Supply Line Requirement |
1-Inch NPT Gas Line |
| Burner Coil & Wrap |
Schedule 80 Coil with Stainless Steel Wrap |
| Burner Exhaust Stack Size |
8 Inches |
| Discharge Hose Dimensions |
50 Feet x 3/8 Inch |
| Wand & Nozzle Assembly |
Dual Wand with Side Handle Valve; 0°, 15°, 25°, 40° Quick-Change Nozzles |
| Overall Dimensions (L x W x H) |
47" x 29" x 46" |
| Shipping Weight |
660 lbs |
| Payment Terms |
Wire Transfer Only (No Credit Cards Accepted) |
Cross-Reference SKUs
| 20220180 |
| CS-20220180 |
| CS20220180 |
| CLEANSTORM-20220180 |
| CLEANSTORM20220180 |
Tips and Additional Information
Pre-Installation & Gas/Venting Setup: Before firing the unit, verify that the stationary skid is anchored on a level surface and plumbed to a dedicated 1-inch LP gas supply line with gas-rated pipe thread sealant on all NPT fittings. Because this is a fuel-burning stationary system, you must install an 8-inch exhaust flue stack and ensure adequate room make-up air in accordance with local codes; consult a licensed HVAC professional prior to installation. Verify that your electrical supply matches the 230V, 40A single-phase requirement and inspect all high-pressure quick-connect O-rings, swivel fittings, and hose crimps for proper alignment before pressurizing.
Chemical Injector & Hose Routing: The included low-pressure downstream chemical injector is calibrated to draw detergent efficiently through the supplied 50-foot x 3/8-inch hose. If you plumb this stationary unit into an extended overhead boom or facility pipeline exceeding 50 feet, you must relocate the chemical injector to within 50 feet of the trigger gun to maintain proper Venturi suction. Use the dual-wand side handle valve rather than non-live fixed-orifice restrictions to switch smoothly between low-pressure soap draw and full 2000 PSI rinse pressure without surging the unloader.
Frequently Asked Questions
Q: What gas line size and venting are required for the Clean Storm 20220180?
This stationary LP gas unit requires a 1-inch LP gas supply line and an 8-inch exhaust vent stack. Proper combustion make-up air and venting must be configured by a qualified HVAC professional if installed indoors.
Q: Can I use a discharge hose longer than 50 feet with the built-in chemical injector?
Yes, you can run longer hoses or facility piping, but the low-pressure chemical injector must be relocated within 50 feet of the trigger gun so backpressure does not prevent detergent draw.
Q: What electrical circuit is needed to run the 10 HP motor?
The unit requires a 230-volt, single-phase power supply rated for 40 amps and includes a 10-foot power cord.
Q: How is the payment processed for this stationary pressure washer build?
This specialized industrial build requires payment via wire transfer only; credit cards are not accepted.
Warranty & Safety Information
Warranty & Operating Limits: Coverage applies to defects in materials and workmanship under normal industrial use within rated operating limits. Operating the system beyond its 2000 PSI pressure rating, exceeding the 195° F burner output limit, feeding inlet water hotter than 140° F into the pump, running the pump dry, or operating with improper voltage or gas pressure will void coverage.
Safety Hazards: Fuel-burning forced-air burners produce carbon monoxide and exhaust gases; operate outdoors or install proper 8-inch exhaust venting and make-up air systems to prevent asphyxiation hazards. Never point the high-pressure wand at people, animals, or electrical equipment, as 2000 PSI water streams at 195° F can cause severe injection injuries and thermal burns. Always verify that the secondary pressure pop-off valve and thermal overload protection remain unobstructed and unmodified.
|