

Clean Storm 20220181, Stationary Hot Water Pressure Washer 5.5 GPM 2500 PSI LP Gas Fired 230V 40A Steel Industrial Cleaning System
Description
The Clean Storm 20220181 Stationary LP Gas Fired Hot Water Pressure Washer delivers 5.5 GPM at 2500 PSI for continuous, heavy-duty industrial grease, oil, and grime removal. Powered by a robust 10 HP, 230V, 40 Amp single-phase totally enclosed electric motor and heated by an efficient forced-air Liquid Propane (LP) gas burner, this unit reaches outlet temperatures up to 195° F. Built on an industrial-coated steel tubing skid frame, it features a commercial triplex plunger pump with ceramic plungers, stainless steel valves, and a durable Schedule 80 heating coil wrapped in stainless steel. Ideal for fixed wash bays and commercial facilities, this stationary unit connects directly to a 1-inch gas supply line and includes a 50-foot high-pressure hose, dual-wand trigger gun, and quick-change nozzles. Note: Wire transfer payment only on this custom build; credit cards are not accepted.
Features
- Industrial 10 HP, 230V, 40 Amp, 1-phase electric motor is totally enclosed and equipped with thermal overload protection for continuous duty cycles.
- Commercial triplex plunger pump constructed with wear-resistant ceramic plungers and corrosion-resistant stainless steel valves.
- Dual-layer pump protection featuring a pressure-regulating unloader valve, secondary pressure pop-off relief valve, and mechanical thermal protection.
- High-efficiency forced-air LP gas burner system engineered around a heavy-duty Schedule 80 heating coil with a protective stainless steel outer wrap.
- Precision temperature management with an adjustable thermostat and high-limit safety switch capping water temperature at 195° F.
- Rugged stationary skid frame fabricated from industrial-coated steel tubing to resist corrosion in wet wash-bay environments.
- Low-pressure downstream chemical injection system optimized for applying concentrated liquid detergents and degreasers through the included 50-foot hose.
- Heavy-duty trigger gun paired with a dual lance wand and side handle valve for seamless switching between high-pressure rinse and soap application, complete with 0°, 15°, 25°, and 40° quick-connect nozzles.
Applications
- Permanent commercial fleet washing bays for semi-trucks, delivery vans, buses, and municipal utility vehicles.
- Heavy construction, agricultural, and mining equipment maintenance facilities requiring high-temperature degreasing.
- Industrial manufacturing plants, machine shops, and fabrication floors for removing cutting oils, grease, and production residue.
- Food processing plants, commercial kitchens, and sanitation stations requiring 195° F hot water washdowns.
- Multi-bay wash stations utilizing plumbed high-pressure piping networks (with chemical injector relocation within 50 feet of the trigger gun).
Specifications
| Brand |
Clean Storm |
| Model Number / Part Number |
20220181 |
| Mounting Configuration |
Stationary Skid Frame |
| Frame Construction |
Industrial Coated Steel Tubing |
| Water Output Type |
Hot Water (Up to 195° F) |
| Operating Pressure |
2500 PSI |
| Flow Rate |
5.5 GPM |
| Motor Horsepower |
10 HP |
| Power Source |
Electric Motor (Totally Enclosed, Thermal Overload Protected) |
| Electrical Requirements |
230 Volt / 40 Amp / 1 Phase |
| Power Cord Length |
10 Feet |
| Pump Type & Materials |
Industrial Triplex Plunger Pump with Ceramic Plungers & Stainless Steel Valves |
| Pump Safety & Thermal Protection |
Mechanical Thermal Protection, Unloader Valve, Secondary Pressure Pop-Off |
| Max Pump Inlet Water Temperature |
140° F |
| Burner Fuel Type |
L.P. Gas (Liquid Propane) |
| Burner Technology |
Forced Air Burner with Adjustable Thermostat & Temp Limit Switch |
| Heating Coil |
Schedule 80 Coil with Stainless Steel Wrap |
| Gas Supply Connection |
1-Inch Gas Line |
| Exhaust Stack Diameter |
8 Inches |
| High-Pressure Hose |
50 Feet x 3/8 Inch |
| Wand & Nozzle Assembly |
Heavy-Duty Trigger Gun, Dual Wand with Side Handle Valve, 0°, 15°, 25°, 40° Quick-Change Nozzles |
| Overall Dimensions (L x W x H) |
53" x 33" x 58" |
| Shipping Weight |
660 lbs |
Cross-Reference SKUs
| 20220181 |
| CS-20220181 |
| CS20220181 |
| CLEANSTORM-20220181 |
| CLEANSTORM20220181 |
| 2022-0181 |
Tips and Additional Information
Payment & Ordering Notice: This unit is a specialized stationary industrial build and requires payment via Wire Transfer only; credit cards are not accepted.
Gas Line & Venting Installation: This stationary machine must be plumbed to a dedicated 1-inch LP gas supply line. Because the burner combusts fuel, indoor installations strictly require an 8-inch exhaust stack vent and adequate make-up air supply. Always consult a licensed HVAC and gas piping professional prior to installation.
Chemical Injector Placement: The factory-installed low-pressure chemical injector is calibrated for use with the included 50-foot hose. If you plumb this machine into a facility-wide pipeline or use hoses exceeding 50 feet, you must relocate the downstream chemical injector to within 50 feet of the trigger gun to maintain proper suction.
Pre-Startup & Thread Sealing: Before powering on, verify pump crankcase oil levels, inspect all high-pressure fittings, and apply chemical-resistant PTFE thread sealant or tape to non-swivel NPT pipe threads. Do not use thread sealant on O-ring or flare-style swivel connections. Ensure incoming feed water does not exceed 140° F to prevent premature pump seal failure.
Frequently Asked Questions
Q: Can this LP gas pressure washer be installed indoors inside a wash bay?
A: Yes, it is designed for stationary indoor or outdoor installation, provided that indoor setups are properly vented using the 8-inch burner exhaust stack and supplied with adequate combustion make-up air per local HVAC and building codes.
Q: What size gas line is required to run the burner at full capacity?
A: The forced-air LP gas burner requires a connection to a 1-inch gas supply line to ensure sufficient fuel volume and pressure for reaching the 195° F maximum water temperature.
Q: Can I run a 100-foot hose or hard-pipe this unit to multiple wash drops and still draw soap?
A: Yes, you can extend the high-pressure line, but backpressure over 50 feet will prevent the low-pressure chemical injector from drawing detergent. For runs longer than 50 feet, you must relocate the chemical injector downstream within 50 feet of the trigger gun.
Q: What electrical hookup does the 10 HP motor require?
A: The unit features a 10-foot power cord and requires a dedicated 230 Volt, 40 Amp, single-phase electrical circuit.
Q: How do I switch between high-pressure rinsing and low-pressure detergent application?
A: The included dual wand assembly features a side handle valve. Opening the side handle valve drops the line pressure to activate the low-pressure chemical injector, while closing it restores full 2500 PSI cleaning pressure.
Warranty & Safety Information
Warranty Coverage & Void Conditions: Covered under Clean Storm manufacturer warranty against defects in materials and workmanship. Warranty coverage will be voided by improper gas line sizing, failure to provide adequate exhaust venting and make-up air, operating the pump without water, exceeding the 140° F maximum pump inlet water temperature, freezing damage, or unauthorized modifications to the burner, unloader, or high-limit safety switches.
Operating Limits & Safety Hazards: Never exceed the maximum operating rating of 2500 PSI or 195° F outlet water temperature. Carbon monoxide and combustion gas hazard: operate outdoors or install proper 8-inch exhaust venting and make-up air systems indoors. High-pressure fluid injection hazard: never point the spray wand at people, animals, or electrical components, and always wear appropriate personal protective equipment (PPE) including eye, hearing, and thermal protection.
|