

Clean Storm 20220211, Electric Cold Water Pressure Washer Cart 1450 PSI 2 GPM 2 HP Roto-Molded Polyethylene Commercial Industrial
Description
The Clean Storm 20220211 is a heavy-duty electric cold water pressure washer engineered to deliver 1450 PSI at 2 GPM for commercial and industrial facility maintenance. Housed inside a rotationally molded, heavy-wall polyethylene cart chassis, this unit shields its 2 HP industrial electric motor and triplex plunger pump from moisture, debris, and job site impacts. Operating on standard 120V single-phase power with a 35-foot GFCI-protected cord, it provides reliable, fume-free cleaning power indoors and outdoors. The integrated low-pressure chemical injection system enables rapid detergent application directly through the variable-pattern multi-reg nozzle, while the durable triplex pump utilizes ceramic plungers and stainless steel valves for extended service life under continuous duty cycles.
Features
- Rotationally molded heavy-wall polyethylene cart chassis provides superior impact resistance and environmental protection for internal drive components.
- Industrial 2 HP totally enclosed fan-cooled (TEFC) electric motor with built-in thermal overload protection prevents overheating during extended operation.
- Commercial-grade triplex plunger pump features wear-resistant ceramic plungers, corrosion-resistant stainless steel valves, and an integrated unloader valve.
- Mechanical pump thermal relief protection safeguards seals and internal pump components from heat buildup during bypass mode.
- Low-pressure chemical injection system activates smoothly by sliding the multi-reg variable spray pattern nozzle into the low-pressure detergent position.
- Molded frame design incorporates dedicated onboard chemical storage capacity to streamline detergent transport and application.
- Includes a 50-foot by 3/8-inch high-pressure discharge hose and a 35-foot power cord equipped with an inline Ground Fault Circuit Interrupter (GFCI) plug.
Applications
- Indoor warehouse, manufacturing plant, and food processing facility floor and equipment washdowns where exhaust fumes are prohibited.
- Commercial fleet maintenance, automotive detailing bays, and municipal service garages.
- Agricultural machinery, dairy barn, and livestock facility sanitation.
- Property management, hospitality, and institutional exterior surface cleaning and degreasing.
- Heavy-duty industrial degreasing requiring downstream chemical injection and heated inlet water up to 160° F.
Specifications
| Brand |
Clean Storm |
| Model / Part Number |
20220211 |
| Water Temperature Type |
Cold Water (Accepts Inlet Water up to 160° F / 71° C) |
| Power Source |
Electric Motor (Totally Enclosed, Thermal Overload Protected) |
| Horsepower |
2 HP |
| Electrical Requirements |
120 Volt, 20 Amp, 1-Phase |
| Power Cord |
35' Length with Integrated GFCI Plug |
| Operating Pressure |
1450 PSI (100 Bar) |
| Flow Rate |
2.0 GPM (7.6 LPM) |
| Pump Type & Internals |
Industrial Triplex Plunger Pump with Ceramic Plungers & Stainless Steel Valves |
| Pressure & Thermal Control |
Integrated Unloader Valve & Mechanical Thermal Protection |
| Chemical Injection |
Low-Pressure Downstream Injector (Nozzle-Activated) |
| Nozzle Type |
Multi-Reg Variable Pattern Nozzle (High/Low Pressure Adjustment) |
| Discharge Hose |
50' x 3/8" High-Pressure Hose (3/8" Quick-Connect / NPT Fittings) |
| Chassis & Mounting |
Roto-Molded Heavy-Wall Polyethylene Cart Frame |
| Dimensions (L x W x H) |
25" x 16" x 46" |
| Shipping Weight |
165 lbs |
Cross-Reference SKUs
| 20220211 |
| CS-20220211 |
| CS20220211 |
| CLEANSTORM-20220211 |
| 2022-0211 |
Tips and Additional Information
Before initial startup, inspect the triplex pump crankcase oil level via the sight glass and verify that the shipping plug has been replaced with the vented dipstick to prevent seal blowouts. Apply PTFE thread seal tape or liquid thread sealant to all rigid NPT male pipe connections, while leaving O-ring sealed quick-connect couplers and swivel fittings un-taped to ensure proper seating. Always verify smooth swivel action on the 3/8-inch high-pressure hose and trigger gun connection to prevent hose kinking and premature crimp failure. Connect the unit exclusively to a dedicated 120V, 20-amp circuit—avoid using unrated extension cords that can cause voltage drop and trip the motor thermal overload or GFCI plug. Purge all air from the water supply line by squeezing the trigger gun before powering on the electric motor, and never allow the pump to run in bypass mode for extended periods without triggering the wand.
Frequently Asked Questions
Q: Can I feed warm or hot water into the Clean Storm 20220211 cold water pressure washer?
Yes. Although this unit does not have an onboard burner to heat water, its industrial triplex pump and mechanical thermal protection system are rated for a maximum inlet water temperature of 160° F (71° C), allowing you to connect it to a tempered or hot water supply line for enhanced degreasing.
Q: How do I activate the soap and detergent injection feature?
The unit features a low-pressure chemical injection system controlled directly at the wand. Slide the multi-reg variable pattern nozzle forward into the low-pressure setting; the drop in line pressure automatically creates suction through the chemical draw tube to mix concentrate detergent with the water stream.
Q: What electrical outlet is required to run this 2 HP electric pressure washer?
The motor draws 20 amps at 120 volts (single-phase) and requires a dedicated 20-amp receptacle (typically a NEMA 5-20R outlet). Always test the built-in GFCI plug on the 35-foot power cord before each use.
Q: What is the advantage of a roto-molded polyethylene cart over a tubular steel frame?
Rotationally molded heavy-wall polyethylene will not rust, dent, or corrode when exposed to water, harsh industrial detergents, or wet environments. It also encloses and shields the 2 HP motor and triplex pump from accidental impacts and water spray.
Warranty & Safety Information
The Clean Storm 20220211 is backed by the manufacturer's standard commercial equipment warranty covering defects in materials and workmanship on the motor, triplex pump, and roto-molded chassis. Warranty coverage is voided by running the pump dry, exceeding the 160° F maximum inlet water temperature, operating on inadequate voltage/amperage circuits, freezing damage, or unauthorized modification of the unloader valve.
Safety Warning: High-pressure fluid streams at 1450 PSI can cause severe injection injuries; never point the spray wand at people, animals, or electrical equipment. Always test the 35-foot GFCI power cord prior to operation, wear ANSI-approved eye protection and slip-resistant footwear, and relieve all system pressure before disconnecting the 3/8-inch discharge hose or servicing the pump.
|