

Clean Storm 620048SS, Marine Grade Hose Clamp Size 48 316 Stainless Steel
Description
The Clean Storm 620048SS Marine Grade Hose Clamp secures heavy-duty hoses from 2-9/16 inches to 3-1/2 inches in diameter using corrosion-resistant all-316 stainless steel construction. Designed for harsh saltwater, chemical, and high-moisture environments, this Size 48 worm gear clamp features a 1/2-inch wide band, housing, and slotted hex screw made entirely from marine-grade 316 stainless steel to prevent rust, pitting, and galvanic corrosion where standard 304 stainless steel clamps fail.
Features
- 100% 316 Marine-Grade Stainless Steel: Band, housing, and screw are manufactured from molybdenum-alloyed 316 stainless steel for superior resistance to chlorides, saltwater, and harsh industrial chemicals.
- 1/2-Inch Wide Perforated Band: Distributes clamping pressure evenly around the hose circumference to create a leak-free seal without cutting into soft rubber, silicone, or PVC hose walls.
- 5/16-Inch Slotted Hex Head Screw: Allows fast, high-torque installation and removal using either a standard flathead screwdriver, nut driver, or socket wrench.
- Wide Clamping Range (Size 48): Accommodates outer hose diameters from 2-9/16 inches (65 mm) up to 3-1/2 inches (89 mm) for versatile fitting across marine and industrial lines.
- Smooth Inner Band Edges: Engineered to minimize hose abrasion and extrusion during high-torque tightening and thermal expansion cycles.
Applications
- Marine vessel bilge pumps, raw water cooling intakes, exhaust lines, and below-waterline plumbing systems
- Commercial carpet cleaning extractors, truckmount vacuum hoses, and solution recovery tank connections
- Chemical transfer lines, wastewater treatment equipment, and washdown systems
- Coastal construction, agricultural irrigation, and high-salinity industrial piping
- Automotive, RV, and heavy-duty diesel coolant, intake, and intercooler hose connections
Specifications
| Brand |
Clean Storm |
| Part Number |
620048SS |
| SAE Size |
Size 48 |
| Clamping Diameter Range |
2-9/16 in. to 3-1/2 in. (65 mm to 89 mm) |
| Band Width |
1/2 in. (12.7 mm) |
| Band Material |
316 Stainless Steel |
| Housing Material |
316 Stainless Steel |
| Screw Material |
316 Stainless Steel |
| Drive Type |
5/16 in. Hex Head with Slotted Drive |
| Finish |
Natural Passivated Stainless Steel |
| Clamp Style |
Worm Gear Hose Clamp (Non-Swivel) |
| Recommended Installation Torque |
30 to 45 in-lbs (verify against hose manufacturer limit) |
| Operating Temperature Range |
-65°F to 800°F (-54°C to 427°C) hardware rating (limited by hose material) |
Cross-Reference SKUs
| 620048SS |
| 620-048SS |
| Clean Storm 620048SS |
| Midland 620048SS |
| Midland 620-048SS |
| SAE Size 48 316SS |
| 620048 SS |
Tips and Additional Information
Pre-Installation Inspection: Before installing, measure the outside diameter (O.D.) of the hose after it is fully seated over the barbed fitting or pipe nipple to confirm it falls near the middle of the 2-9/16 in. to 3-1/2 in. adjustment range. Inspect the worm gear threads and band slots for debris or burrs.
Alignment & Positioning: Position the clamp at least 1/8 inch to 1/4 inch behind the end of the hose and behind the barb bead, ensuring the band sits squarely perpendicular to the hose axis. Avoid tightening directly over the sharp edge of a fitting nipple.
Thread Sealing & Galling Prevention: Worm gear hose clamps provide mechanical radial compression rather than pipe-thread sealing; do not apply PTFE tape or pipe dope to the worm screw. Because 316 stainless steel threads can experience galling under rapid friction, tighten smoothly with a hand nut driver rather than a high-speed impact driver.
Live vs. Non-Live System Maintenance: Always depressurize and isolate live fluid, exhaust, or suction lines before loosening or adjusting clamps. For marine below-waterline or high-vibration engine applications, double-clamping with two clamps staggered 180 degrees apart is recommended, and all clamps should be re-torqued after initial heat and pressure cycles.
Frequently Asked Questions
Q: What is the difference between this all-316 stainless steel clamp and a standard marine clamp?
Many standard marine clamps use 300-series (304) stainless steel or mix a 316 band with a 304 screw. The Clean Storm 620048SS uses 316 stainless steel across all three components—band, housing, and screw—providing superior protection against chloride pitting and crevice corrosion in constant saltwater immersion.
Q: How do I know if Size 48 (2-9/16 in. to 3-1/2 in.) will fit my hose?
Measure the outside diameter (O.D.) of your hose once it is pushed onto the fitting, not the inside diameter (I.D.) printed on the hose wall. If the installed O.D. measures between 2.56 inches and 3.50 inches, this clamp will fit properly.
Q: Can I use an impact driver to tighten the 5/16-inch hex screw?
No. Using high-speed power tools on stainless steel worm gear screws generates heat that can cause thread galling (cold welding) or strip the perforated band slots. Use a manual 5/16-inch nut driver or torque wrench for controlled tightening.
Warranty & Safety Information
Warranty Coverage & Void Conditions: Covered under standard manufacturer defect warranty against material flaws and workmanship defects upon receipt. Warranty is void if the clamp is over-torqued beyond structural limits, installed with impact tools causing thread galling, modified, or exposed to chemicals incompatible with 316 stainless steel.
Pressure, Temperature & Safety Hazards: While 316 stainless steel hardware withstands extreme temperatures, actual working pressure and temperature ratings are governed by the hose material, fitting barb design, and installation torque. Never exceed the lowest rated component in the assembly. Wear eye and hand protection during installation, trim or shield excess protruding band tail to prevent laceration hazards, and never service pressurized or high-temperature lines while the system is active.
|