Ebac Dd200 Industrial Desiccant Dehumidifier - Dd200 - Desiccant Dehumidifiers

Ebac DD200 Industrial Desiccant Dehumidifier [DD200]

Click to enlarge

Your Price: $2,826.76
Part Number: DD200
Quantity:
Estimated shipping cost: $ 169.00

Product Options
Shipping Surcharges:

Ebac: DD200 Desiccant Dehumidifier 10502SS-US

INTRODUCTION
Dehumidifiers remove moisture from the air that is circulating through the unit.
The resulting reduction of relative humidity helps prevent rust, rot, mould,
mildew and condensation within the room, or other enclosed spaces where
the dehumidifier is used.
The DD200 is of the desiccant wheel type designed to dry air by passing a
large volume of air, the “process” air through a slowly rotating Silica gel rotor.
Silica gel is a hygroscopic material that absorbs moisture direct from the air.
As the air passes through the rotor the humidity of the air is reduced, whilst
the moisture content of the rotor is increased. A smaller volume of air, the
reactivation air, is heated by an internal heater and passes through a portion
of the rotor in the opposite direction. As this heated air passes through the
rotor it will “reactivate” it by removing the moisture content from the silica gel
material. The reactivation air will leave the humidifier as warm, moist air and
must be vented to outside of the building.
Continuous circulation of the room air through the dehumidifier unit gradually
reduces the relative humidity in the room.
The DD200 dehumidifier is a robust, compact unit designed to control the
humidity in the enclosed space in which it is placed. The casing is fabricated
from Stainless Steel 304 and has been designed for the exacting conditions
which can prevail in offices, shops, houses, restaurants, public houses etc. It
combines lightness and compactness with high reliability and strength. Carry
handles are provide to contribute to its portability.
The unit is thermally protected and will switch off if the maximum operating
temperature of 40ºC is exceeded.
The dehumidifier has a single filter positioned at the air inlet and is used to
clean the air entering the dehumidifier.

KEY DESIGN FEATURES
• Stainless Steel Construction
• Auto / Manual Mode Selection
• Electronic Controls
• High Capacity PTC Heater
• Remote Humidistat Facility
• Low Temperature Operation
• Ammeter

SPECIFICATIONS
MODEL: DD200
HEIGHT: 340mm
WIDTH: 330mm
DEPTH: 380mm
WEIGHT: 17 Kg
DRY AIRFLOW: 180 M³/HR
WET AIRFLOW: 50 M³/HR
POWER SUPPLY: 115V, 1 ph, 60Hz
POWER 0.8 kW (max)
FINISH: Stainless steel 304
DEHUMIDIFICATION CAPACITY
(AT 27°C AND 60% RH)
0.9kg/h
NOISE 67dB(A)

INSTALLATION
POSITIONING:
The DD200 is designed for indoor use. Position the dehumidifier unit in the
center of the room to be conditioned if at all possible.
NOTE: Both the air inlets and outlets of the dehumidifier unit must have clear
space around them and not be obstructed in anyway.
DUCT CONNECTION
The wet air outlet from the dehumidifier must be exhausted to outside of the
room being dried by means of a suitable duct. All duct connections to the
dehumidifier have been designed for connections to standard size ducts.
The duct should be as short as possible to reduce the risk of condensation of
the wet air. The duct should slope downwards away from the unit to stop any
condensed water from flowing back into the unit.
The dry air outlet is also provided with a means of attaching a duct. This can
be used to direct the air towards more severe damp patches.
WIRING:
The DD200 is provided with a standard plug and is designed to operate from
a 13 Amp supply.
IMPORTANT – The wires in the mains lead are coloured in accordance with
the following code:
GREEN…………….…………EARTH
WHITE..……………………….NEUTRAL
BLACK.....…………………….LIVE
If the supply cord is damaged it must be replaced by qualified Ebac Industrial
Products Ltd personnel or other similar qualified persons in order to avoid
hazard.

OPERATION
The electrical controls are located on the front of the unit. They are:
• ON / OFF Switch
0 Dehumidifier OFF
1 Dehumidifier ON
• Humidity Switch
M Dehumidifier in continuous operation
A Dehumidifier operation by means of an external
humidistat
• An ammeter is provided to display the current used by the unit.
• An hour counter is provided to display the total time the unit has been
in operation
• A socket is provided for connection of a external humidistat
To start the dehumidifier, turn the On / Off switch to position 1.
Turn the humidity switch to position M.
After a slight delay the fan will operate – air can be felt blowing from the air
outlets and the heater will come on.
The unit will operate continuously at this setting.
Note. The DD200 is controlled by an electronic circuit board and uses PTC
(positive temperature coefficient) heater technology to provide the heat
necessary to “reactivate” the rotor.
At switch on, the ammeter will initially show a higher current for a few
seconds, prior to settling to a steady value. This is normal.
If an external humidistat control is fitted, turn the humidity switch to position A.
Depending on the setting of the humidistat, the dehumidifier may switch off as
the relative humidity in the room decreases. As the humidity increase the unit
will automatically switch back on.
The Humidistat plug supplied should be wired using pins numbered 1 & 2.
Pin 3 is not required. See diagram 5010307 at back of manual.

AIR MOVING SYSTEM:
The DD200 is a single fan balanced system providing both the “Process” air
and “Regeneration” air flow. As the air passes over the rotor, it will be heated
as a result of the regeneration cycle. The air leaving the unit will be hotter
than the air entering
During normal operation some parts of the dehumidifier may become hot. This
is normal.
HIGH TEMPERATURE CUT OUT:
The DD200 dehumidifier has been designed to work in ambient conditions of
-20ºC to +40ºC. Should the temperature in the room become excessive an
overheat protector will operate, switching off the PTC heaters. The fan and
drive motor will continue to operate. This is a manual reset device. Prior to
resetting the protector, check that the dehumidifier is installed correctly and
the ambient temperature does not exceed 40°C.
See repairs section for details on resetting device.
DEHUMIDIFICATION CAPACITY
Approximate capacity in Kg/h at different inlet process air temperature and
relative humidity (%)

DD200	DD300	DD400
Specification	10502SS-US	10501SS-US	10500SS-US	Units
Height	13.5	14.5	15	inches
Width	13	14	17	inches
Depth	15	16	21.5	inches
Weight	37.5	44	59.5	lbs
Voltage	115	115	220	V
Phase	1	1	1	-
Frequency	60	60	60	Hz
Power	TBC	TBC	TBC	watts
Current	TBC	TBC	TBC	A
Airflow - Dry Air	TBC	TBC	TBC	cfm
Airflow - Wet Air	TBC	TBC	TBC	cfm
Noise Level	TBC	TBC	TBC	dba
Typical Extraction (27ºC60%RH)	TBC	TBC	TBC	pints/day
Process Air Duct Size	TBC	TBC	TBC
Regen Air Duct Size	TBC	TBC	TBC

Features	10502SS-US	10501SS-US	10500SS-US	Units
ON/OFF Control	Y	Y	Y
Carrying HandleS	Y	Y	Y
Amp Meter	Y	Y	Y
Electronic Controls	Y	Y	Y
Manual / Automatic Modes	Y	Y	Y
Hour Meter	Y	Y	Y
Remote Humidity Sensor	Y	Y	Y
High Capacity PTC Heater	Y	Y	Y
Rubber Anti Vibration Feet	Y	Y	Y
Single Air Inlet Design	Y	Y	N
Dual Air Inlet Design	N	N	Y
Free Standing	Y	Y	Y
High Temperature Safety Cutout	Y	Y	Y
Min Temp	-4	-4	-4	ºF
Max Temp	104	104	104	°F
Moulded Mains Plug	Y	Y	Y
Air Filters	Y	Y	Y
Stainless Steel Construction	Y	Y	Y
Humidstat	O	O	O
Inlet Duct Attachments	O	O	O

As a reminder, customers MUST be present to sign for shipments. Ebac is not liable for any damages or warranty claims that are brought to our attention after a customer has left a note telling the carrier that it is OK TO LEAVE a shipment at the customer's residence or delivery address without them being present. All shipments should be carefully inspected before accepting delivery to ensure item is delivered free of damage.

check stock

See Brochure

Wire Diagram 1

Owners Manual

Wire Schematics

0100721 dc

Steambrite will ship the Ebac DD200 Industrial Desiccant Dehumidifier [DD200] by either Fedex, UPS, USPS, or Freight Quote, and will normally be shipped within 2-5 business days (if in stock). Equipment small enough to be sent by ground should typically arrive within 3-5 business days after shipment. Large Equipment could take in excess of 6-8 working days to arrive after shipment, and ground shipping times are not guaranteed. Special order, or custom build items may take up to 30 days.
Next day, two day, and three day services are available.
Click here for our full shipping policy. Specifications are subject to change without notice.
Steam Brite Inc shall have no obligation or liability to buyer whether arising in contract (including warranty) tart (including active, passive or imputed negligence) other otherwise for loss of use, revenue or profit, or any other incidental or consequential damages with respect to any non-conformance or defect in any items provided here under. You our customer agrees to indemnify Steam Brite Inc and to hold it harmless from and against any and all claims, cost, liabilities, damages and expenses, including attorney's fees, resulting from personal injury or property damaged caused by the Products.
Warranty Disclaimer: Buyer's sole and exclusive remedy for defects in the products shall be as provided in the manufactures's warranty and any other rights provided by law against the manufacturer. Steam Brite, Inc makes no other than as specified in this agreement. All other warranties, express or implied, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are hereby disclaimed.

This product was added to our store on Wednesday 21 July, 2010.

Product Datasheet

DD200 for only $2,826.76 - Steambrite's price on the Desiccant Dehumidifiers - DD200 extractor, Equipmentcarpet cleaning equipment, Equipment flood restoration, Equipment carpet cleaning machine,

Ebac: DD200 Desiccant Dehumidifier 10502SS-US