Used Dri-Eaz 126946 Control Panel Kit for DrizAir 1200 and Evolution Dehumidifiers
Replacement electronic control panel for select 115-volt Dri-Eaz DrizAir 1200 and Evolution portable dehumidifiers. This updated control panel replaces several earlier control-board and panel numbers, including 08-00259, 08-00259S and 103238.
Important Compatibility Notice
The current replacement control panel is intended for compatible Dri-Eaz DrizAir 1200 and Evolution 115-volt dehumidifiers only. It is not compatible with DrizAir 2000 or DrizAir 2400 dehumidifiers. This unit was harvested from a unit that the freon leaked out.
| Manufacturer |
Dri-Eaz / Legend Brands |
| Current replacement panel |
126946 |
| Listed part number |
08-00259 / 08-00259S |
| Additional reference number |
103238 |
| Operating voltage |
115–120 volts AC |
| Compatible equipment |
Dri-Eaz DrizAir 1200 and Dri-Eaz Evolution dehumidifiers |
| Not compatible with |
DrizAir 2000, DrizAir 2400 or 230-volt machines |
| Product type |
Dehumidifier control panel and printed circuit board assembly |
Replacement Part References 
Depending on the age of the machine, catalog, distributor or previous repair history, this part may be associated with one or more of the following numbers:
- 126946
- 08-00259
- 08-00259S
- 103238
- S252
- DP-0800259-EA
- PDR10A
Reference numbers are supplied to help identify the product. Always order according to the required replacement part and confirmed machine compatibility.
Fits These Dri-Eaz Dehumidifiers
- Dri-Eaz DrizAir 1200 portable dehumidifier
- Dri-Eaz Evolution portable dehumidifier
- Applicable 115-volt versions using the compatible control-panel configuration
Does not fit: DrizAir 2000, DrizAir 2400, 230-volt machines or unrelated Dri-Eaz LGR dehumidifier models. Do not rely only on the appearance of the panel when determining compatibility.
Installation Information
Dri-Eaz has used more than one wiring arrangement in DrizAir 1200 machines. Installation is not necessarily a simple wire-for-wire exchange on every older dehumidifier. The correct procedure depends on the part number and wiring configuration of the original control panel.
The factory instructions contain separate procedures and wiring diagrams for different versions of the DrizAir 1200, as well as separate instructions for the Evolution dehumidifier. Review the complete instructions before disconnecting any wiring.
Open Dri-Eaz Control Panel Installation Instructions
Before servicing: Drain or purge the water from the dehumidifier, disconnect the power cord and verify that the machine is completely unplugged. Incorrect wiring can damage the replacement control panel or other electrical components.
Recommended service tools 
- Phillips-head screwdriver
- Ratchet and extension
- 1/4-inch, 5/16-inch and 3/8-inch sockets
- Needle-nose pliers
- Camera or phone for photographing the original wiring before disassembly
Before Ordering
- Confirm that the machine is a Dri-Eaz DrizAir 1200 or Evolution.
- Confirm that the dehumidifier operates on approximately 115–120 volts.
- Inspect and record the part number printed on the original control panel.
- Compare the existing wiring arrangement with the factory installation instructions.
- Do not order this panel for a DrizAir 2000 or DrizAir 2400.
If the original label is missing or unreadable, send clear photographs of the machine identification label, front control panel and wiring on the back of the existing panel before ordering.
Related Defrost Sensor
Depending on the diagnosis and condition of the machine, the control panel may be used with the Dri-Eaz 08-00260 / 119488 defrost sensor. The sensor is sold separately unless specifically stated otherwise.
View Dri-Eaz 08-00260 Defrost Sensor
Frequently Asked Questions
Will this panel fit a Dri-Eaz DrizAir 2000 or 2400?
No. The current replacement is no longer approved as a replacement for the DrizAir 2000 or DrizAir 2400.
Does the replacement panel have a voltage-selector switch?
No. The current replacement panel is designed for 115-volt applications and does not include the older voltage-selector arrangement.
Is professional installation recommended?
Yes. Installation should be performed by a qualified appliance or restoration-equipment repair technician who can identify the existing wiring configuration and follow the applicable factory wiring diagram.
Can I return the panel after installing it?
Electrical parts are commonly nonreturnable after installation. Confirm the machine model, voltage, original panel number and wiring configuration before placing the order.
Ordering and Shipping Notice
Website availability does not guarantee that the part is physically stocked in the Steam-Brite San Antonio warehouse. The order may ship from local inventory, a regional warehouse or the manufacturer. Special-order parts may require additional processing time.
Product photographs are provided for reference. Manufacturers may revise circuit-board components, relays, labels, terminal locations or other details without changing the service replacement part number. Orders are fulfilled according to the part number purchased.
Electrical Part Notice: Control boards can be damaged by incorrect wiring, failed motors, shorted solenoids, defective pumps, moisture intrusion, voltage problems or other unresolved machine faults. Replacing a damaged panel without diagnosing the original cause may damage the new panel. Installation labor, diagnostic labor and consequential damage are not included unless expressly stated.
English
French
Spanish
German
Italian
Portuguese
