

WestPak 20-0018 Upholstery Hand Tool Valve Repair Kit – Mytee B141A
WestPak Part Number: 20-0018
Mytee Part Number: B141A
Valve Type: 200 PSI Offset Hand Tool Valve
Application: Carpet Cleaning, Upholstery Cleaning, Auto Detailing and Spot Cleaning Tools
The WestPak 20-0018 Valve Repair Kit is designed to service compatible 200 PSI offset brass trigger valves commonly used on professional upholstery cleaning tools, carpet cleaning hand wands, automotive detailing tools and portable extractor accessories.
If your upholstery cleaning wand continues spraying after releasing the trigger, develops a water leak around the valve stem, or has a trigger that becomes difficult to operate, the internal valve components may require cleaning, lubrication or replacement.
Common Symptoms of a Worn or Sticking Upholstery Tool Valve
- Water continues spraying after the trigger is released.
- The spray nozzle drips or leaks when the trigger is not depressed.
- The trigger becomes difficult to depress or release.
- The internal valve piston sticks or does not return smoothly.
- Water leaks around the brass valve stem or packing nut.
- The valve no longer shuts off water flow completely.
How to Service Your Upholstery Cleaning Tool Trigger Valve
Many upholstery cleaning tools use a brass packing nut located directly underneath the valve trigger. This nut provides access to the valve stem packing and sealing components.
- Turn off the extractor pump and completely relieve water pressure before servicing the valve.
- Disconnect the upholstery cleaning tool from the pressurized solution hose.
- Locate the brass packing nut directly underneath the trigger lever.
- Carefully loosen and remove the packing nut to access the valve stem and packing components.
- Inspect the piston, O-rings and packing assembly for wear, damage, mineral deposits or contamination.
- Clean reusable components and apply a small amount of compatible silicone-based valve lubricant to the appropriate moving seals and packing components.
- Replace damaged or worn components using the WestPak 20-0018 repair kit where applicable.
- Reassemble the valve, tighten the packing nut appropriately, and check for smooth trigger operation.
- Reconnect the solution hose, restore water pressure, and inspect for leaks and proper shutoff operation.
Important: Do not overtighten the packing nut. Excessive tightening can restrict valve stem movement and prevent the trigger from operating smoothly.
Why Does My Upholstery Cleaning Tool Keep Spraying?
One common cause of an upholstery cleaning tool that will not stop spraying is a sticking valve piston or worn internal sealing components.
Over time, cleaning chemicals, mineral deposits, dirt and normal wear can interfere with the movement of the valve stem. The piston may not return completely to its closed position when the trigger is released.
In some cases, disassembling the packing assembly, cleaning the internal components and applying the proper lubricant can restore normal operation without replacing the entire brass valve.
If the internal seals or packing components are damaged, the WestPak 20-0018 Repair Kit provides a repair option for compatible valves.
Compatible Valve and Replacement Part References
- WestPak 20-0018 – Valve Repair Kit
- Mytee B141A – Cross-reference part number
- WestPak 200OS – Compatible 200 PSI Offset Valve Application
Compatibility Notice: This repair kit is intended for compatible 200 PSI offset hand tool valves. Not all brass trigger valves use the same internal components.
Before ordering, verify the valve manufacturer, model number and internal component configuration. Do not assume compatibility based solely on the appearance of the brass valve.
Repair Your Existing Valve Instead of Replacing the Entire Tool
A leaking or sticking upholstery cleaning tool does not necessarily require purchasing a completely new wand.
Servicing the existing brass trigger valve can be a cost-effective solution that helps extend the useful life of professional carpet cleaning and upholstery cleaning equipment.
Order WestPak 20-0018 replacement valve repair parts from Steam-Brite.
Repairs valve below

Note cannot repair valves that have freeze damage.
Can be used with the tool below
|